The member photo gallery is now integrated and live!!  All user albums and pictures have been ported from old gallery.


To register send an e-mail to admin@bmwr65.org and provide your location and desired user name.

Author Topic: Tach thinks my RPM is always exactly 4500!  (Read 141 times)

Offline Steve

  • Newbie
  • *
  • Posts: 61
  • 1979 R65 with 175k miles
Tach thinks my RPM is always exactly 4500!
« on: November 14, 2026, 08:48:52 AM »
My 1979 R65?s tach had always worked well but its illumination light went out so I opened it up. The tracing of that circuit had blown. I repaired it. It blew again, and the tracing for Pin 6 as well. So I went through the whole motorcycle fixing questionable grounds and connections. Then I repaired the broken tracings again. Now all the lights work and circuits aren?t blowing. But the tach, when you turn the ignition on, goes to 4500 RPM and stays there rock solid until you turn the ignition off. Any thoughts?

Offline Bob_Roller

  • Global Moderator
  • Mt. Olympus Resident
  • *****
  • Posts: 9144
  • -7 hours GMT
Re: Tach thinks my RPM is always exactly 4500!
« Reply #1 on: November 14, 2026, 01:12:00 PM »
Sounds like you have a stray voltage getting into that circuit .

I would check the black wire that comes off of the dual coil setup you hav and see if it's getting voltage someplace it shouldn't be getting .
You repaired the copper tape circuit in the tachometer printed circuit board possibly you got solder or whatever you used for the repair into another circuit in the tachometer .
'81 R65
'82 R65 LS
'84 R65 LS
'87 Moto Guzzi V65 Lario
'02 R1150R
Riding all year long since 1993 .
I'll give up my R65, when they pry my cold dead hands from the handlebars !!!!!

Offline georgesgiralt

  • Mt. Olympus Resident
  • ****
  • Posts: 1394
  • I Love YaBB 2!
Re: Tach thinks my RPM is always exactly 4500!
« Reply #2 on: November 15, 2026, 02:56:02 AM »
Hello,
These tachs use a circuit converting frequency to voltage.
As yours goes strait to 4500 RPM, no external reason for this because if the engine is not running, no alternating current is present in the whole machine.
So you have a short somewhere in the tach feeding some voltage to the meter, thus making it to move to 4500 RPM.
Check the printer circuit for a blob of solder and/or a seized meter wire which got deteriorated and make contact somewhere it should not...
If you do not find the fault, as these tachs are almost indestructible, they are plentiful on the second hand marked and do not ask for premium prices. So , change it. Just my 2 ?

Offline Steve

  • Newbie
  • *
  • Posts: 61
  • 1979 R65 with 175k miles
Re: Tach thinks my RPM is always exactly 4500!
« Reply #3 on: November 15, 2026, 09:44:09 AM »
On that last suggestion, I find that a company in Germany sells used tachs, and they look correct, but the ones in better shape are for the R45, not the R65. He uses designations like "BMW R 45 248 1980". Are they the same?

Offline georgesgiralt

  • Mt. Olympus Resident
  • ****
  • Posts: 1394
  • I Love YaBB 2!
Re: Tach thinks my RPM is always exactly 4500!
« Reply #4 on: November 15, 2026, 11:55:50 AM »
As the ignition circuit is the same, the electronics is the same. However, as the max RPM is different, the face plate has to be replaced to match the correct red line...
So, IMHO, buy one, swap the electronics and Bob's your uncle... Or search for a used one near you.