The member photo gallery is now integrated and live!!  All user albums and pictures have been ported from old gallery.


To register send an e-mail to admin@bmwr65.org and provide your location and desired user name.

Author Topic: grabby clutch  (Read 295 times)

Offline Happy Eeyore

  • Newbie
  • *
  • Posts: 33
grabby clutch
« on: November 08, 2026, 05:04:05 AM »
My 79 R65 is running like a champ now and I get it out and ride it around the north Georgia mountain roads both paved and gravel.   When I got the bike I replaced the clutch disk when I put in a new rear seal and lubed the splines.  I did not replace the clutch spring or the pressure plate.  The old spring and pressure plate looked ok.  But first  gear seems grabby to me.  First gear in the R65 is pretty high but that ratio is what it is.

The clutch cable and the  position of the arm seem right .  But tryin to carefully and smoothly slip the clutch seems difficult.  I have had two oil heads  before in which I just replaced the clutch discs and they both  had clutches as smooth as silk.  Should I replace the spring and pressure plate and see it that changes the clutch engagement or is that rough clutch just a characteristic of the design. 

Winter is coming and I have a heated shop and enjoy working on the bike as much as I like riding it.  But I do not want to try and fix something that cannot be fixed .   What do the old hands think?

Offline Barry

  • Mt. Olympus Resident
  • ****
  • Posts: 5158
Re: grabby clutch
« Reply #1 on: November 09, 2026, 10:15:32 AM »
Hard to say if anything wrong because even a good clutch is quite abrupt at the best of times and takes a little getting used to. My 79 was grabby when I bought the bike but it improved considerably with use. I put that down to corrosion after being stood for years but it might have been just me getting better at using it.  Is a new disc grabby before it's worn in ?  I don't know the answer to that because I didn't need to replace mine in 18 years of use. 

Barry Cheshire, England 79 R45

Offline Bob_Roller

  • Global Moderator
  • Mt. Olympus Resident
  • *****
  • Posts: 9144
  • -7 hours GMT
Re: grabby clutch
« Reply #2 on: November 09, 2026, 12:53:21 PM »
Was this happening before the clutch disc replacement ??
I did a generic search for R65 grabbing clutch, may want to check the cable adjustment, it was mentioned .
What grease did you use on the splines ??
By chance did you aply too much grease on the splines ??
Grease can be pushed off the splines then get thrown onto the clutch disc .
« Last Edit: November 09, 2026, 12:58:39 PM by Bob_Roller »
'81 R65
'82 R65 LS
'84 R65 LS
'87 Moto Guzzi V65 Lario
'02 R1150R
Riding all year long since 1993 .
I'll give up my R65, when they pry my cold dead hands from the handlebars !!!!!

Offline dogshome

  • Lives in Foothills of Mt. Olympus
  • **
  • Posts: 449
Re: grabby clutch
« Reply #3 on: November 10, 2026, 11:39:23 AM »
If you've not had the little arm off the back of the clutch yet (that the cable connects to) take it off. It's very easy. You may find the needle roller bearing is siezed. It still operates, but makes things a lot harder. The R65 does not suffer the same clutch pushrod issues as other Airheads, but if you have the arm off, it is easy (should be....) to pull out and inspect. It should be oily from the gearbox.

Replacing the little needle bearing (and centre piece) involves use of a het gun and a hammer  8)

Oh, if you didn't put moly grease on the splines, you can do it by undoing the two engine bolts, and the four gearbox to bell housing bolts (and a couple of silence fasteners) and pull the engine forward a little. You can get a grease-loaded artists brush in the gap.
« Last Edit: November 10, 2026, 11:42:37 AM by dogshome »
肉(r?u)包子(zi)打狗 (meat+bun(2nd and 3rd)+hit+dog)
* Literally: To hit a dog with a meat-bun.:-O

Offline Happy Eeyore

  • Newbie
  • *
  • Posts: 33
Re: grabby clutch
« Reply #4 on: November 10, 2026, 02:57:32 PM »
Thanks for all the replies.  When I had the bike apart 4 months ago, I lubed the splines which were good, put  in a new disc, and new rear seal, checked the trans seals and play, lubed the throw out little disc, lubed the rod felt and put her back together.  I looked at the spring and pressure plate and other clamping disc.  Everything looked to be in good shape.  I adjusted the throw out bolt yesterday to get the engagement point about midway on the clutch lever  and that seemed to help.  It it not now grabby enough to warrant a redo.  I have never ridden another R65 so the high first gear and that jettter  may be a characteristic of the bike. 

Offline dogshome

  • Lives in Foothills of Mt. Olympus
  • **
  • Posts: 449
Re: grabby clutch
« Reply #5 on: November 14, 2026, 03:16:27 PM »
My bike has a 900 FD (33:11). That needs a little care. I don't remember the standard FD causing problem, but glad you solved it  :thumbsup:
肉(r?u)包子(zi)打狗 (meat+bun(2nd and 3rd)+hit+dog)
* Literally: To hit a dog with a meat-bun.:-O